Patient Transfer Equipment

Manual Height Adjustable Patient Transfer Stretcher for Safe Hospital Transportation

Safe patient transportation depends on more than moving a stretcher from one department to another. Caregivers need stable braking before transfer, suitable working height, protective side rails, controlled steering and secure patient support throughout the journey.

The JH-OCT103 manual height adjustable patient transfer stretcher is designed around these everyday hospital transport requirements. It combines 560–860 mm mechanical height adjustment, a maximum load capacity of 300 kg, gas-spring assisted backrest adjustment, ABS lift-up side rails, central braking and a retractable fifth wheel.

An oxygen cylinder holder, telescopic stainless steel IV pole and mattress with two safety straps further support patient transportation between hospital departments.

560–860 mm Manual Crank Height Adjustment

Mechanical Height Adjustment without an Electric Lift System

The JH-OCT103 uses a manual crank mechanism to adjust the overall stretcher height from approximately 560 mm to 860 mm.

The foldable stainless steel crank can be operated to raise or lower the patient platform according to the transfer situation. This mechanical design does not rely on an electric actuator for height adjustment.

Adapt the Stretcher before Patient Transfer

Different hospital beds and patient support surfaces may have different working heights. The adjustable platform allows caregivers to change the stretcher height before beginning an assisted patient transfer.

Once the required position has been reached, the crank can be folded away to reduce interference during routine transportation.

300 kg Maximum Load Capacity

Robust Support for Hospital Patient Transport

The JH-OCT103 has a specified maximum load capacity of 300 kg.

For hospital buyers, load capacity is an important specification when selecting patient transport equipment for different patient groups. It should be considered together with the stretcher dimensions, platform configuration and intended clinical application.

Gas-Spring Assisted Backrest Adjustment

0–75° ±5° Upper-Body Positioning

The backrest can be adjusted from a flat position to approximately 75° ±5° using a gas-spring assisted mechanism.

The system is designed for convenient operation and allows the caregiver to adjust the back section with one hand.

This provides a practical way to change the patient's upper-body position before, during or after hospital transportation.

ABS Lift-Up Side Rails with Gas-Spring Damping

Patient Protection during Transportation

Two ABS lift-up side rails are installed on the stretcher. Each side rail measures approximately 1080 × 260 × 35 mm.

When raised, the rails provide lateral protection around the patient platform during transportation.

Controlled Lowering of the Side Rails

The side rail lowering mechanism incorporates gas-spring damping. This provides a more controlled lowering action when the rail is released.

When closer access to the patient is required, caregivers can lower the rail before transfer or other patient-handling procedures.

Two Safety Straps for Additional Patient Support

Designed for Patient Security during Transport

The supplied 20 mm mattress is equipped with two patient safety straps.

When appropriately positioned and used, the straps provide additional patient restraint during transportation, complementing the protective function of the side rails.

This combination is particularly useful when patients require additional support while being moved between clinical areas.

Central Braking System for Secure Stationary Positioning

Four Ø150 mm Central-Control Casters

The stretcher is equipped with four 150 mm central-control casters and a foot-operated central braking system.

The caster specification includes wear-resistant, anti-entanglement construction together with protective dust covers.

From Transport Mode to Stationary Patient Handling

Before patient transfer or positioning begins, caregivers can operate the central braking system to secure the stretcher.

After the patient is ready for transportation, the brake can be released and the stretcher returned to mobile operation.

Retractable Fifth Wheel for Directional Control

Two Mobility Modes for Different Hospital Environments

An independent central fifth wheel is incorporated into the stretcher chassis, with operating pedals positioned on both sides.

When the fifth wheel is retracted, the stretcher can move freely on its main casters for turning and positioning.

When the fifth wheel is engaged, it provides directional assistance to help the stretcher maintain a straighter forward path during transportation.

Spring-Damped Fifth-Wheel Mechanism

The central fifth wheel also incorporates a spring damping mechanism, providing additional compliance when the stretcher moves across uneven surfaces.

One-Piece Molded ABS Patient Platform

Integrated Handles for Caregiver Operation

The patient platform is manufactured from molded ABS engineering plastic with a one-piece construction.

Integrated handles are positioned around the four corners of the platform, providing additional gripping points for caregivers during stretcher positioning and transportation.

Reinforced Carbon Steel Frame Construction

Built for Repeated Hospital Transport

The main stretcher frame is manufactured from welded carbon steel and finished with electrostatic powder coating.

The longitudinal frame members use 50 × 30 × 2 mm rectangular hollow steel sections, while the triangular support components are formed from 2.5 mm cold-rolled steel plate.

This structural configuration provides a solid mechanical foundation for the patient platform, height adjustment system and mobility chassis.

Integrated Oxygen Cylinder Holder

Support for Oxygen during Patient Transportation

An oxygen cylinder holder is positioned at the head end of the stretcher and is designed for an oxygen cylinder with a diameter of approximately 135 mm.

This allows compatible oxygen equipment to remain with the patient when respiratory support is required during intra-hospital transportation.

Telescopic Stainless Steel IV Pole

The stretcher includes a telescopic stainless steel IV pole for infusion support during patient transportation.

Diagonal IV pole sockets are positioned at the head and foot ends, allowing the pole position to be selected according to the patient's care requirements.

A Patient Transfer Workflow Built around Safety and Control

Before the Transfer

Position the stretcher beside the hospital bed, operate the central brake and use the manual crank to adjust the platform to the required working height.

During Assisted Patient Handling

Lower the ABS side rail to create closer lateral access. Once the patient is correctly positioned, return the rail to its protective position and use the safety straps as appropriate.

During Transportation

Release the central brake and select the required steering mode. Free caster movement supports turning and positioning, while the fifth wheel can be engaged when greater directional control is required.

At the Destination

Engage the central brake before patient handling begins. The gas-spring assisted backrest can then be adjusted according to the required upper-body position.

Key Technical Specifications

Model: JH-OCT103.

Product Type: Manual Height Adjustable Patient Transfer Stretcher.

Overall Size: 1930 × 640 × 560–860 mm.

Height Adjustment: 560–860 mm.

Height Adjustment System: Manual crank mechanism.

Crank: Foldable stainless steel handle.

Backrest Adjustment: 0–75° ±5°.

Backrest System: Gas-spring assisted.

Maximum Load Capacity: 300 kg.

Frame: Welded carbon steel construction.

Main Longitudinal Beam: 50 × 30 × 2 mm rectangular hollow steel.

Triangular Support: 2.5 mm cold-rolled steel plate.

Surface Finish: Electrostatic powder coating.

Patient Platform: One-piece molded ABS engineering plastic.

Side Rails: ABS lift-up side rails with gas-spring damping.

Side Rail Size: 1080 × 260 × 35 mm.

Main Casters: 4 × Ø150 mm central-control casters.

Brake System: Central braking system.

Directional System: Retractable central fifth wheel.

Fifth Wheel: Ø100 mm.

Fifth-Wheel Suspension: Spring damping mechanism.

Oxygen Cylinder Holder: Suitable for approximately Ø135 mm oxygen cylinder.

IV Pole: Telescopic stainless steel IV pole.

Mattress: 20 mm Oxford-fabric mattress.

Safety Straps: 2 pcs.

Net Weight: 75 kg.

Gross Weight: 108 kg.

Packing: Wooden case.

Packing Size: 1990 × 740 × 670 mm.

For Hospital Wards and Intra-Hospital Patient Transportation

The JH-OCT103 provides a practical mechanical solution for hospitals that need adjustable patient transport equipment without an electric height-adjustment system.

Its combination of manual 560–860 mm height adjustment, 300 kg maximum load capacity, gas-spring backrest, ABS side rails, two safety straps, central braking and fifth-wheel directional control supports routine patient movement between hospital care areas.

Explore our Patient Transfer Equipment range for additional hospital stretchers and patient transport solutions.

You can also explore our Hospital Bed range for additional hospital patient-care equipment.

For technical specifications, bulk purchasing, available configurations or OEM/ODM requirements, contact us with your project requirements.